Don’t Let Winter Crack Your Water System

Oct 28, 2026

If your water recycling system sits outside, the first hard freeze of the season is coming for it. And it only takes one cold night.

Water expands about 9% when it freezes. That expansion must go somewhere, and it usually finds the weakest point in your system: a sensor housing, a valve body, a pump casing, a fitting or a tank wall. The damage often doesn’t show up until things thaw, when you come in and find a flood, a dead sensor or a pump that won’t prime. By then you’re losing production and paying for parts.

The good news is that freeze damage is entirely preventable. Here’s what to protect, and the four ways to do it.

What’s at risk

  • Sensors. pH probes, clarity (turbidity) sensors, flow and pressure sensors are the most sensitive components on your system. A pH probe that freezes is usually done. Ice can crack the glass bulb or ruin the reference junction.
  • Plumbing. Exposed pipe, hose and fittings freeze first because they hold small volumes of water with lots of surface area. Low spots and dead legs that don’t see flow are the usual culprits.
  • Valves. Solenoid, ball and float valves trap water in their bodies. Ice can split the housing or seize the internals, including your automatic freshwater fill if you have one.
  • Pumps. Water sitting in a pump casing can crack it or damage seals.
  • Tanks. A thick ice cap puts stress on tank walls and can lock up mixers, floats and level sensors.

Four ways to protect your system

Most shops will use a combination of these. The colder your climate and the more exposed your system, the more layers you want.

1. Cover and heat

The simplest step is to get your system out of the wind. An enclosure, insulated cover or simple shelter around the system cuts heat loss dramatically. Wind chill doesn’t change the air temperature, but it pulls heat out of exposed equipment much faster.

For colder regions, add a heat source inside the enclosure. A thermostatically controlled heater rated for wet, outdoor or agricultural environments can keep the space above freezing. Pay special attention to sensor locations.

2. Heat-tape exposed plumbing

Heat tape (heat trace cable) wrapped along exposed lines keeps water from freezing inside the pipe. A few tips to get it right:

  • Use self-regulating heat tape that is rated for the pipe material you’re wrapping. Many of our systems use plastic pipe, and not every tape is approved for it.
  • Cover the full exposed run, including valves, unions and the short stubs that are easy to miss.
  • Add pipe insulation over the tape if the manufacturer allows it. Tape alone loses a lot of its heat to the air.
  • Plug into a GFCI-protected outdoor outlet and check that the tape is warm before the first cold night.

3. Keep water moving overnight

Full Circle Water - Moving Water to Prevent Freezing

 

Moving water is much harder to freeze than still water. During cold stretches, leaving your system circulating overnight keeps water flowing through the pumps, plumbing and sensors instead of sitting in place.

This works best as part of a plan, not on its own. Circulation protects the lines water is flowing through, but dead legs, drain lines and anything outside the flow path can still freeze. Pair it with covering and heat tape for those areas.

4. Add a livestock tank heater

Farmers have been keeping water from freezing outdoors for a long time, and their tools work for us too. A livestock tank heater (also called a stock tank de-icer) placed in your settling or clean water tank keeps an ice cap from forming and holds water temperature above freezing.

  • Choose a heater rated for your tank material. Poly tanks need a heater designed for plastic, or a guard that keeps the element off the tank wall.
  • Look for a built-in thermostat so it only runs when it needs to.
  • Plug into a GFCI-protected outlet and route the cord where it won’t be damaged or pulled into the tank.
  • Keep it clear of mixers, floats and level sensors.

Shutting down for an extended period?

If your shop is closing for the holidays or the system won’t run for several days in freezing weather, the safest move is to drain it:

  1. Drain tanks, pumps, valves and low points in the plumbing.
  2. Remove the pH probe and store it in its storage solution indoors. Never let it dry out, and never let it freeze.
  3. Bring in any other removable sensors if your system allows it.
  4. Leave drain valves open so any water left behind has room to expand.

Before restarting, check for cracks and leaks, reinstall and calibrate the pH probe, and watch your readings closely for the first few hours.

Use your data

If your system has remote monitoring, it’s one of your best freeze-protection tools. Watch for warning signs like dropping flow, pressure that won’t hold, or a sensor reading that suddenly goes flat. Those can be the first signs of ice in the lines. Catching it early can be the difference between a quick thaw and a cracked housing.

Your winter checklist

ALWAYS CHECK WITH LOCAL CODES AND ORDINANCES FOR ANY ADDITIONS YOU DO TO ENSURE THEY ARE IN COMPLIANCE

  • Cover or enclose the system and block the wind.
  • Add a thermostatically controlled heat source in colder climates.
  • Heat-tape and insulate all exposed plumbing and valves.
  • Run the system overnight during cold stretches.
  • Add a livestock tank heater to keep tanks from icing over.
  • Have a drain-down plan for extended shutdowns, including pH probe storage.
  • Test every heater and heat tape before the first freeze.
Not sure where your system is most exposed?
Our support team can walk through your setup and help you build a winter plan before the cold hits. Call 320-529-4035 or visit fullcirclewater.com

More Blog Posts

Controlling Bacteria in Your Closed-Loop Water System

A practical guide to odor, sludge, and sanitizer use in countertop fabrication shops. Applies to systems running liquid coagulant or GreatWhite. The short version Bacteria in a recirculating water system are normal. Every shop has them. They only become a problem when...

Made in Minnesota.
Built for the World.

In a time where outsourcing is the norm and shortcuts are easy to come by, we’ve chosen a different path. One rooted in craftsmanship, accountability, and pride in where we come from. Everything we build starts right here in Minnesota. Inside our facility in St....